Version: v0.0.0-...-ae31599 Latest Latest

This package is not in the latest version of its module.

Go to latest
Published: Oct 8, 2015 License: BSD-3-Clause Imports: 7 Imported by: 0



Package flate implements the DEFLATE compressed data format, described in RFC 1951. The gzip and zlib packages implement access to DEFLATE-based file formats.



View Source
const (
	NoCompression = 0
	BestSpeed     = 1

	BestCompression    = 9
	DefaultCompression = -1


This section is empty.


func NewReader

func NewReader(r io.Reader) io.ReadCloser

NewReader returns a new ReadCloser that can be used to read the uncompressed version of r. If r does not also implement io.ByteReader, the decompressor may read more data than necessary from r. It is the caller's responsibility to call Close on the ReadCloser when finished reading.

The ReadCloser returned by NewReader also implements Resetter.

func NewReaderDict

func NewReaderDict(r io.Reader, dict []byte) io.ReadCloser

NewReaderDict is like NewReader but initializes the reader with a preset dictionary. The returned Reader behaves as if the uncompressed data stream started with the given dictionary, which has already been read. NewReaderDict is typically used to read data compressed by NewWriterDict.

The ReadCloser returned by NewReader also implements Resetter.


type CorruptInputError

type CorruptInputError int64

A CorruptInputError reports the presence of corrupt input at a given offset.

func (CorruptInputError) Error

func (e CorruptInputError) Error() string

type InternalError

type InternalError string

An InternalError reports an error in the flate code itself.

func (InternalError) Error

func (e InternalError) Error() string

type ReadError

type ReadError struct {
	Offset int64 // byte offset where error occurred
	Err    error // error returned by underlying Read

A ReadError reports an error encountered while reading input.

func (*ReadError) Error

func (e *ReadError) Error() string

type Reader

type Reader interface {

The actual read interface needed by NewReader. If the passed in io.Reader does not also have ReadByte, the NewReader will introduce its own buffering.

type Resetter

type Resetter interface {
	// Reset discards any buffered data and resets the Resetter as if it was
	// newly initialized with the given reader.
	Reset(r io.Reader, dict []byte) error

Resetter resets a ReadCloser returned by NewReader or NewReaderDict to to switch to a new underlying Reader. This permits reusing a ReadCloser instead of allocating a new one.

type WriteError

type WriteError struct {
	Offset int64 // byte offset where error occurred
	Err    error // error returned by underlying Write

A WriteError reports an error encountered while writing output.

func (*WriteError) Error

func (e *WriteError) Error() string

type Writer

type Writer struct {
	// contains filtered or unexported fields

A Writer takes data written to it and writes the compressed form of that data to an underlying writer (see NewWriter).

func NewWriter

func NewWriter(w io.Writer, level int) (*Writer, error)

NewWriter returns a new Writer compressing data at the given level. Following zlib, levels range from 1 (BestSpeed) to 9 (BestCompression); higher levels typically run slower but compress more. Level 0 (NoCompression) does not attempt any compression; it only adds the necessary DEFLATE framing. Level -1 (DefaultCompression) uses the default compression level.

If level is in the range [-1, 9] then the error returned will be nil. Otherwise the error returned will be non-nil.

func NewWriterDict

func NewWriterDict(w io.Writer, level int, dict []byte) (*Writer, error)

NewWriterDict is like NewWriter but initializes the new Writer with a preset dictionary. The returned Writer behaves as if the dictionary had been written to it without producing any compressed output. The compressed data written to w can only be decompressed by a Reader initialized with the same dictionary.

func (*Writer) Close

func (w *Writer) Close() error

Close flushes and closes the writer.

func (*Writer) Flush

func (w *Writer) Flush() error

Flush flushes any pending compressed data to the underlying writer. It is useful mainly in compressed network protocols, to ensure that a remote reader has enough data to reconstruct a packet. Flush does not return until the data has been written. If the underlying writer returns an error, Flush returns that error.

In the terminology of the zlib library, Flush is equivalent to Z_SYNC_FLUSH.

func (*Writer) Reset

func (w *Writer) Reset(dst io.Writer)

Reset discards the writer's state and makes it equivalent to the result of NewWriter or NewWriterDict called with dst and w's level and dictionary.

func (*Writer) Write

func (w *Writer) Write(data []byte) (n int, err error)

Write writes data to w, which will eventually write the compressed form of data to its underlying writer.

Jump to

Keyboard shortcuts

? : This menu
/ : Search site
f or F : Jump to
y or Y : Canonical URL